Product ID:EC-1386 STRUCTURAL EPOXY ADHESIVE
MSDS Date:09/30/1988
FSC:8040
NIIN:01-027-4901
MSDS Number: BMCDZ

3M CENTER

3M CENTER BLDG
ST PAUL, MN 55144-0001
US

Emergency Phone: 612-733-1110

Info Phone: 612-733-1110

Cage: 07884

MECHANICAL SPRING CORP

BROOKLYN, NY 11217-2702 US

Telephone: 718-852-0116

Cage: 07884

EPOXY RESIN

CAS: 25068-38-6

RTECS: KD4380000

Fraction By Weight: 70-80%

ACRYLONITRILE BUTADIENE POLYMER

CAS: 9003-18-3

Fraction By Weight: 10-20%

DICYANDIAMIDE

CAS: 461-58-5

Fraction By Weight: 1-10%

AMORPHOUS SILICA

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 1-10%

OSHA PEL 20 MPPCF TWA

ACGIH TLV: 6MG/M3 TWA

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:EYE CONTACT: MAY CAUSE EYE IRRITATION.
VAPORS OF HEATED PRODUCT OR DUST FROM GRINDING, CUTTING, AND
SANDING OPERATIONS ON THE CURED PRODUCT MAY CAUSE EYE IRRITATION.
SKIN CONTACT: MAY CAUSE SKIN IRRIT ATION AND ALLERGIC REACTION ON
PROLONGED OR FREQUENT CONTACT. INHALATION: VAPORS FROM CURING
OPERATIONS AND DUST FROM *
Effects of Overexposure:* CUTTING, GRINDING, OR SANDING OPERATIONS MAY
CAUSE RESPIRATORY IRRITATION. SYMPTOMS INCLUDE COUGHING, SNEEZING,
AND ITCHING. INGESTION: MAY CAUSE MINOR DIGESTIVE SYSTEM
IRRITATION.

First Aid:EYE CONTACT: IMMEDIATELY FLUSH EYES WITH LARGE AMOUNTS OF
WATER FOR AT LEAST 10 MINUTES. GET MEDICAL ATTENTION. SKIN CONTACT:
WIPE OFF CONTAMINATION. WASH AFFECTED AREA WITH SOAP AND WATER.
INHALATION : MOVE TO FRESH AIR IF SYMPTOMS OCCUR. IF SWALLOWED: DO
NOT INDUCE VOMITING. IMMEDIATELY CALL PHYSICIAN OR POISON CONTROL
CENTER.

Flash Point:0F,-18C
Extinguishing Media:CARBON DIOXIDE, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:FIRE FIGHTERS SHOULD BE EQUIPPED WITH
SELF-CONTAINED BREATHING APPARATUS WHEN FIGHTING FIRES INVOLVING
THIS MATERIAL.
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:VENTILATE THE AREA. OBSERVE PRECAUTIONS FROM
OTHER SECTIONS. COLLECT SPILLED MATERIAL. PLACE IN A CONTAINER.

Other Precautions:FOR INDUSTRIAL OR PROFESSIONAL USE ONLY. AVOID
CONTACT WITH EYES, SKIN AND CLOTHING. AVOID BREATHING EMISSIONS
FROM CURING OPERATIONS AND DUST FROM CUTTING, GRINDING AND SANDING
OPERATIONS.

Ventilation:PROVIDE VENTILATION SUFFICIENT TO CONTROL EMISSIONS/DUST.
VENT CURING OVENS OUTDOORS OR TO AN EMISSION CONTROL DEVICE.
Protective Gloves:INPERVIOUS GLOVES
Eye Protection:SAFETY GLASSES
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING. LAUNDER
CONTAMINATED CLOTHING BEFORE REUSE.
Supplemental Safety and Health

Spec Gravity:1.150 (WATER=1)
Viscosity:100 CENT
Solubility in Water:ESSENTIALLY NIL
Appearance and Odor:CREAM COLORED, VISCOUS PASTE, LOW ODOR.
Percent Volatiles by Volume:0%

Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:THERMAL DECOMPOSITION OR BURNING MAY
PRODUCE C, H, N DECOMPOSITION PRODUCTS.

Waste Disposal Methods:INCINERATE BULK PRODUCT AFTER MIXING WITH
FLAMMABLE MATERIAL IN AN INDUSTRIAL OR COMMERICAL FACILITY.
DISPOSAL SHOULD BE IN ACCORDANCE WITH APPLICABLE REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.